Choosing the right portable generator starts with the load, not the generator’s advertised size. This guide gives you a reusable worksheet for calculating running and starting watts, checking voltage and phase, comparing fuel and runtime, and confirming that a generator is suitable for a jobsite, event, facility, or backup application.
Overview
The answer to “What size generator do I need?” depends on every device that may operate at the same time. A compact generator may handle lights, chargers, and small tools, while a construction generator may be needed for compressors, pumps, welders, heaters, or several high-demand tools running together.
Begin with the equipment nameplate, owner’s manual, or manufacturer specification. Record four basic details for each load:
- Running watts: the power required while the equipment is operating normally.
- Starting watts: the temporary surge required by many motors and compressors when they start.
- Voltage: such as 120, 208, 230, or 480 volts, as applicable to the equipment.
- Phase: single-phase or three-phase, where relevant.
Watts can often be estimated from volts multiplied by amps, but nameplate information is preferable. When a motor’s starting requirement is not listed, do not guess casually. Ask the equipment manufacturer, rental provider, electrician, or generator dealer for a suitable estimate.
A basic sizing calculation is:
- Add the running watts for all equipment that will operate at the same time.
- Identify the largest starting-watt demand among motor-driven loads.
- Add that starting demand to the running load of the other equipment already operating.
- Compare the result with the generator’s usable continuous rating, not only its brief peak rating.
For example, if lights and chargers use 1,000 running watts, a saw uses 1,800 running watts and 3,600 starting watts, and a small compressor uses 1,200 running watts and 3,000 starting watts, the generator must account for the shared running load and the possibility that either motor starts while the other equipment is operating. Staggering starts may reduce the required capacity, but it should be part of a deliberate operating plan rather than an assumption.
Checklist by scenario
Small tools, lighting, and charging
For a light-duty work area, list battery chargers, task lighting, fans, radios, laptops, and small corded tools. Check whether tools will run simultaneously and whether any saw, grinder, vacuum, or compressor has a substantial startup surge. An inverter-style portable generator may be attractive where reduced noise, cleaner power, or easy transport matters, but confirm that its output matches the connected equipment.
- Count chargers and lights even when each individual load is small.
- Separate occasional-use tools from tools expected to run continuously.
- Confirm the number, type, and rating of receptacles.
- Check whether extension cords are appropriately rated for the distance and load.
Construction and contractor jobsites
Construction work often combines high-starting-current motors, long operating periods, changing crews, and exposure to dust or weather. Create a load schedule for the actual phase of work rather than sizing only for the largest tool in the fleet. A generator used for a saw may not also support a compressor, pump, heater, or welder without additional planning.
- List tools by crew and work area.
- Identify which loads are motor-driven or have heating elements.
- Check whether equipment needs single-phase or three-phase power.
- Confirm the generator’s grounding, distribution, and protection arrangement with a qualified professional.
- Plan cable routing to avoid vehicle paths, standing water, sharp edges, and trip hazards.
If you are comparing a construction generator for sale with a short-term rental, include transport, delivery, fuel, maintenance, and standby time in the comparison. A rental can suit a temporary peak, while ownership may make more sense for repeated utilization and predictable service needs.
Events, mobile service, and outdoor operations
Events and mobile operations add priorities beyond wattage. Noise, emissions, refueling access, footprint, cable length, weather protection, and appearance may affect the practical choice. List audio equipment, food-service appliances, lighting, refrigeration, point-of-sale equipment, and communications equipment separately.
- Ask vendors for the actual electrical requirements of supplied equipment.
- Allow for sensitive electronics and use compatible power distribution equipment.
- Plan fuel storage and refueling without placing people near hot components.
- Confirm the generator can be positioned outdoors with adequate clearance and ventilation.
Emergency or facility backup
Backup power requires a different worksheet. Decide which circuits are essential and which can remain off. Refrigeration, pumps, heating or cooling equipment, elevators, fire protection systems, medical equipment, and communications systems may have different starting and operational requirements. A portable generator must not be connected to building wiring through an improvised cord or an unsuitable transfer arrangement.
Have a qualified electrician determine whether a transfer switch or other approved connection method is required. For critical facilities, document the startup sequence, test procedure, fuel plan, and responsibility for operating the equipment.
What to double-check
| Specification | Why it matters | What to record |
|---|---|---|
| Continuous and peak output | Shows what the generator can sustain and briefly provide. | Both ratings, in watts or kilowatts. |
| Voltage and phase | Prevents incompatibility with tools, panels, and motors. | Required voltage, phase, and frequency. |
| Fuel type | Affects storage, availability, refueling, and operating conditions. | Fuel, tank size, and approved storage method. |
| Runtime | Indicates how often the unit may need refueling at a stated load. | Runtime basis and expected operating load. |
| Portability | Determines whether the unit can be safely moved and positioned. | Weight, wheels, lifting points, and transport method. |
| Noise and enclosure | Important near workers, customers, neighbors, and occupied buildings. | Published noise information and placement limits. |
| Outlets and distribution | Determines how loads can be connected and separated. | Receptacle types, breakers, panels, and cable needs. |
Runtime figures should be treated as planning information, not a guarantee. Actual runtime changes with load, fuel, maintenance, temperature, and operating practice. Likewise, a generator that has enough total wattage may still be unsuitable if it lacks the required voltage, phase, receptacles, protection, or connection equipment.
Before buying used equipment, verify the model plate, operating hours, service history, control-panel function, output under load, and condition of cables and receptacles. The used heavy equipment buying guide and equipment listing verification checklist provide useful general checks for marketplace purchases.
Common mistakes
- Using only running watts: Motors may fail to start or cause voltage dips when surge demand is ignored.
- Adding every peak rating together: This may oversize the unit if those loads never start simultaneously, but it is unsafe to assume a smaller generator without a clear sequence and professional review.
- Ignoring voltage or phase: Total watts cannot correct a mismatch between the generator and the equipment.
- Confusing peak output with continuous capacity: The continuous rating is the more important figure for sustained work.
- Relying on extension cords as distribution: Undersized, damaged, excessively long, or improperly routed cords can create heat and safety hazards.
- Backfeeding a building: Never connect a portable generator to building wiring through an improvised method. Use an approved transfer arrangement installed or reviewed by a qualified electrician.
- Operating indoors or in partially enclosed areas: Engine exhaust can create a serious carbon monoxide hazard. Follow the manufacturer’s placement instructions and applicable workplace and local safety requirements.
- Skipping maintenance: Fuel system condition, oil level, filters, battery condition, grounding, breakers, and receptacles should be inspected according to the manufacturer’s schedule. See the commercial equipment maintenance schedule for a broader recordkeeping approach.
When to revisit
Save the load worksheet and review it before each major project, seasonal planning cycle, or event. Recalculate when you add a tool, change crews, introduce a pump or compressor, expand lighting, or move from single-phase to three-phase equipment. Also revisit the plan when a generator is relocated, fuel availability changes, or a facility adds backup circuits.
Before acting, complete this final checklist:
- Write down every simultaneous load and its running watts.
- Identify starting watts for motors, compressors, pumps, welders, and other surge loads.
- Confirm voltage, phase, frequency, receptacles, and connection method.
- Choose a generator with adequate continuous capacity and a practical starting strategy.
- Compare ownership and rental costs using realistic utilization, delivery, fuel, maintenance, and storage assumptions.
- Inspect the unit, verify its listing and service records, and arrange safe transport if buying used.
- Review placement, ventilation, grounding, cable routing, fuel handling, and emergency procedures before operation.
When the load is uncertain or the generator will connect to building systems, stop at the planning stage and consult a qualified electrician or generator professional. A careful worksheet is useful, but it does not replace equipment-specific instructions or site-specific electrical review.